Motor Control Development Kit with Xilinx Zynq 7020-1C SoC Module

Motor Control Development Kit with Xilinx Zynq 7020-1C SoC Module
€919.00 (1,093.61 € gross) *

Prices plus VAT plus shipping costs

expected to be available on 04-Mar-2022

  • CR00140-02-K1B
  • 0
  • Full production
Quantity Unit price
To 9 €919.00 (1,093.61 € gross) *
From 10 €827.10 (984.25 € gross) *
From 25 €827.10 (984.25 € gross) *
From 50 €735.20 (874.89 € gross) *
From 100 €689.25 (820.21 € gross) *
From 250 €689.25 (820.21 € gross) *
From 500 €615.73 (732.72 € gross) *
From 1000 €615.73 (732.72 € gross) *
Description Downloads Resources
The predecessor of this article is CR00140-02-K1A . All changes are in the Product Change... more
Product information "Motor Control Development Kit with Xilinx Zynq 7020-1C SoC Module"

The predecessor of this article is CR00140-02-K1A. All changes are in the Product Change Notification (PCN).

The Trenz Electronic motor control development kit CR00140-02-K1B includes a CRUVI motor driver module CR00140-02, a carrier board TEB0707-02 and a TE0720-03-61C33MA module with Xilinx Zynq XC7Z020-1CLG484C SoC including a heat sink. Supplied with a universal plug-in power supply with four adapters, a DC motor including cable for CRUVI CR00140 and an 8 GB micro SD card.

Support Package for Motor Control Development available at MathWorks.

The Module: CR00140-02

The Trenz Electronic CR00140 is a CRUVI motor driver module. It supports motors with up to 4 phases up to 40V. 

Key Features

  • On Board
    • MAX 10 CPLD
    • 2 phase current measurement
    • DC_LINK voltage measurement
    • 4 x LEDs (2 power indicator, 2 user)
    • 2 x Pushbutton
  • Interface
    • 4 phase screw terminal motor connector
    • CRUVI for control
      • 1 x high speed connector
    • 6 x 1 pin header for single ended sensors
    • 5 x 2 pin header for differential sensors
  • Power
    • Screw terminal for up to 40V DC motor supply
  • Dimension
    • 68.35 mm x 131 mm

The Module: TE0720-03-61C33MA

The Trenz Electronic TE0720-03-61C33MA is a SoC module integrating a Xilinx Zynq-7020, a Gigabit Ethernet transceiver, 1 GByte DDR3L SDRAM, 32 MByte Flash memory for configuration and operation, and powerful switch-mode power supplies for all on-board voltages. A large number of configurable I/O's is provided via rugged high-speed stacking strips.

Key Features

  • Xilinx Zynq XC7Z020-1CLG484C
  • Rugged for high shock and vibration
  • ARM dual-core Cortex-A9 MPCore
  • 10/100/1000 tri-speed Gigabit Ethernet transceiver (PHY), SGMII accessible on a board-to-board connector
  • USB 2.0 high speed ULPI transceiver
  • 32-bit wide 1 GByte DDR3L SDRAM
  • 32 MByte QSPI Flash memory (for configuration and operation)
  • 8 GByte e.MMC (optional up to 32 GByte)
  • Plug-on module with 2 x 100-pin and 1 x 60-pin Razor Beam High-Speed hermaphroditic Terminal/Socket Strips (regular 4 mm)
  • 152 FPGA I/O's (75 LVDS pairs possible) and 14 MIO's available on board-to-board connectors
  • On-board high-efficiency DC-DC converters
    • 4.0 A x 1.0 V power rail
    • 1.5 A x 1.5 V power rail
    • 1.5 A x 1.8 V power rail
  • System management and power sequencing
  • eFUSE bit-stream encryption
  • AES bit-stream encryption
  • Valid MAC Address and 2K serial EEPROM
  • SHA-256 authentication chip with unique serial number
  • RTC, temperature compensated
  • 3 user LEDs
  • Evenly-spread supply pins for good signal integrity
  • 4 x 5 cm form factor

The Baseboard: TEB0707-02

The Trenz Electronic TEB0707 is a carrier board for 4 x 5 Trenz Electronic modules. It provides three high speed and one low speed CRUVI extension connectors. For more information, please refer to the CRUVI B2B Connectors.

The TEB0707 is integrated with an Intel MAX 10 FPGA as system controller and is equipped with a Micro USB2.0 socket with FTDI to JTAG/UART solution, RJ45 LAN socket, USB A socket, microSD card socket, user LEDs, push buttons and DIP switches for controlling the SoM.

Key Features

Modules

  • 4 x 5 Trenz Electronic modules

RAM/Storage

  • EEPROM (FTDI configuration)

On Board

  • Intel MAX 10 FPGA
  • FTDI FT2223
  • 6 x user LEDs (3 x green, 3 x red)
  • 2 x status LEDs
  • DIP switch
  • Push buttons

Interface

  • Gigabit RJ45 LAN socket
  • MicroSD card socket
  • Micro USB2.0 socket
  • USB A socket
  • 3 x High Speed CRUVI B2B connectors
  • 1 x Low Speed CRUVI B2B connector
  • 4 x Jumpers

Power: 5V input power supply

Dimension: 135 x 68 mm

Scope of Delivery CR00140-02-K1B Motor Control Development Kit

  • 1 x CR00140-02 CRUVI Motor Driver Module
  • 1 x TE0720-03-61C33MA MPSoC Module with Xilinx Zynq XC7Z020-1CLG484C
  • 1 x TEB0707-02 Carrierboard für Trenz Electronic 4 x 5 Modul-Carrier für CRUVI Erweiterungsboards
  • 1 x Pre-installed heatsink for TE0720
  • 1 x BLY172D-24V-4000-1250SI Brushless DC Motor from Anaheim Automation
    • Rated Voltage 24V
    • Rated Speed 4000rpm
    • Rated Power 53W
    • Including encoder, 1250 count per rev, index function (single ended connection)
  • 1 x Universal plug power supply with 4 adapters
  • 1 x 8 GB Class 4 microSDHC-Card
  • 1 x Cable for CR00140

Additional Information

All modules produced by Trenz Electronic are developed and manufactured in Germany.

The online pictures of this product are not a legally binding offer, but are symbol pictures for illustration and presentation only.

Related links to "Motor Control Development Kit with Xilinx Zynq 7020-1C SoC Module"
Downloads
Digilent
OHO-Elektronik
SunDance
Trenz_Electronic - Documents and Design files for Trenz Electronic Products