In case you need an extra case for the OpenLogger.

Connector Standard: Arduino Uno R3 Layout, # of Grove Connectors: 16 total

Connector Standard: 2x6 Standard, number of Grove connectors: 4 total

These mini grabber test clips (also known as micro grabber test clips or IC clips) with leads provide an easy connection from the Analog Discovery, Digital Discovery, or OpenScope MZ to wires, integrated circuits, component leads, and...

The Analog Discovery Studio MTE (Measurement and Test Equipment) cables are the same MTE cables that ship with the Analog Discovery Studio. This set of six cables features male-terminated flywires are perfect for connecting signals to...

This cable is a great option to ensure secure connection with the waveform generator channels for Analog Discovery. It is ideal for connection to small components or parts.

One BNC to alligator clip test probe, designed for use with the BNC Adapter for Analog Discovery.

The Screw Terminal Adapter provides screw terminal block access to the eight analog inputs, 8 digital I/O, Waveform generator, power supplies, and ground signals on the OpenLogger.

Developement carrier board for the TE0724 and compatible modules.

Simple carrier board for Trenz Electronic 4 x 5 modules. It is mainly for the use with TE0720 and TE0715 modules.

Cooling solution especially desgined for Trenz Electronic MPSoC TE0807 (from REV02). Important note: This heatsink requires a so-called gapfiller to be installed to the module.

The Trenz Electronic TEBF0808 carrier board is a baseboard for the Xilinx Zynq Ultrascale+ MPSoC modules TE0803, TE0807 und TE0808

Accessory Kit contains Micro USB cable, Ethernet cable, pre-loaded microSD card and 12V power supply.

Carrier Board for 4 x 5 cm Trenz Electronic SoC's with 3 x Samtec LSHM Series Connectors

Clear, sleek covers made out of plexiglass specifically designed to protect the PYNQ-Z1 Board.

Arrow USB Programmer2 SMD Module is an FT2232H-based JTAG programmer supported by Intel Quartus.

Testes and optimizes the performance of Antennas, RF filters, RF switches, couplers, cables, amplifiers, isolators, mixers

FT2232H based JTAG programmer supported by Intel Quartus.

Narrow SFP to SMA adapter, which has exactly the same width as an SFP slot due to the arrangement of the four SMA connectors.

Low-cost carrier board for Trenz Electronic TE0841 and TE0741 modules.

USB FTDI Interface Board for icoBoard

SMD-plug for DIL with SK5-contacts, no. of contacts: 40

The Z-turn Lite IO Cape extension board is designed specially for Xilinx Zynq-7007S or Zynq-7010 SoC based Single Board Computer Z-turn Lite.

Trenz TE0728 module socket, Power supply via DC jack, 2 x RJ45 Ethernet, SD card connector

The Trenz Electronic TEB0729 carrier board was especially designed and developed for the use of Trenz Electronic module TE0729.

With 1000SI Encoder mounted, compact size and power density, round frame, rated voltage: 24V, rated power: 15 Watts, rated speed: 10000 RPM, 40 mm length

Regulate the Voltage in Robotics and Mechatronics System, Texas Instruments TPS54620 switching regulator, selectable 5V or 3.3V output voltage

BGA standard Heat Sink with thermal tape, external dimensions: 23 x 23 x 18 mm

AC-DC Interchangeable Industrial adapter with 30W single-output

Cooling solution especially desgined for module TE0745-02, flat, custom-fit, dimensions: 80 x 10 x 55 mm

This Logic Analyzer PRO application turns your STEMlab board into an 8 channel Logic Analyzer.

Ideal for probing very high speed signals with minimum signal distortion.

LCR meter App with Software Licence; LCR meter Extensionboard

Accessories Kit for STEMlab Diagnostic Kit (STEMlab 125-10 and STEMlab 125-14)

Interchangeable AC plugs with four adapters and cable, protections: short circuit / overload / over voltage

Acrylic case for STEMlab 125-10 and STEMlab 125-14

Thread M 3, length 5 mm, wrench Size 5,50 mm, thread 1: 5,0 mm, package Content: 1 Standoff

Cooling solution especially desgined for Trenz Electronic module TE0808 from REV03, flat, size: 80 x 10 x 55 mm

The NI myRIO Starter Accessory Kit includes everything you need to get started connecting to and programming the I/O of NI myRIO.

The NI myRIO Embedded Kit contains common sensors, devices, and a display.

Carrier Board especially for TE0714 with Hirose Ultra small SMT coaxial connectors

This High Speed Adapter, for the DIN_USR connector on the Digital Discovery, is an alternative to the 2X16 flywire assembly.

Housing for connector HDR-E26MSG1+

Powerful and compact motor drive/amplifier.

Including Logic Analyzer SW license (unlimited) and Logic Analyzer probes (8ch)

Ribbon Jumper Cable, 51 Position FFC Cable 0.012" (0.30mm) 6.00" (152.40mm), accessory for icoBoard

51 Position FPC Connector Contacts, Top and Bottom 0.012" (0.30mm) Surface Mount, Right Angle, accessory for icoBoard

This power supply is suitable for powering our new PYNQ-Z1, Nexys Video, Genesys 2, and Arty boards. Includes US and EU plug adapters.