JTAG HS2 Programming Cable

€49.99 (59.49 € gross) *

Prices plus VAT plus shipping costs

Ready to ship today,
Delivery time appr. 1-3 workdays

Order number: 24624
In Stock: 14

The Joint Test Action Group (JTAG)-HS2 programming cable is a high-speed programming solution... more

Close menu

Product information "JTAG HS2 Programming Cable"

The Joint Test Action Group (JTAG)-HS2 programming cable is a high-speed programming solution for Xilinx field-programmable gate arrays (FPGAs). The cable is fully compatible will all Xilinx tools and can be seamlessly driven from iMPACT, Chipscope, and EDK. The HS2 attaches to target boards using Digilents 6-pin, 100-mil spaced programming header or Xilinxs 2x7, 2mm connector and the included adaptor.

The PC powers the JTAG-HS2 through the USB port and will recognize it as a Digilent programming cable when connected to a PC, even if the cable is not attached to the target board. The HS2 has a separate Vdd pin to supply the JTAG signal buffers. The high speed 24mA three-state buffers allow target boards to drive the HS2 with signal voltages from 1.8V to 5V and bus speeds of up to 30MBit/sec. (See figure 1) To function correctly the HS2s Vdd pin must be tied to the same voltage supply that drives the JTAG port on the FPGA.

The JTAG bus can be shared with other devices as systems hold JTAG signals at high-impedance except when actively driven during programming. The HS2 comes included with a standard Type-A to Micro-USB cable that attaches to the end of the module opposite the system board connector. The system board connector should hold the small and light HS2 firmly in place.

Need help choosing a board? Let us help you with a Programming Solutions Comparison table!

Features

Analog Devices ADP123AUJZ Linear Regulator
Small, complete, all-in-one JTAG programming solution for Xilinx FPGAs
Compatible with all Xilinx tools
Compatible with IEEE 1149.7-2009 Class T0 - Class T4 (includes 2-Wire JTAG)
Separate Vref drives JTAG/SPI signal voltages; Vref can be any voltage between 1.8V and 5V.
High-Speed USB2 port that can drive JTAG/SPI bus at up to 30Mbit/sec
JTAG/SPI frequency settable by user
Uses micro-AB USB2 connector
SPI programming solution (modes 0 and 2 up to 30Mbit/sec, modes 1 and 3 up to 2Mbit/sec)
Fully supported by Digilent's Adept software and Adept SDK, allowing custom JTAG/SPI applications to be created

Scope of Delivery

USB cable (type-A USB plug, type-AB micro-USB plug)
JTAG HS2 Programmer
6-pin to 2x7-pin Adapter

References

Manufacturer: Digilent Inc.
Manufacturer's article name: JTAG HS2 Programming Cable
Manufacturer's article number: 410-249

Resources

Other Digilent products are available on request.

Related links to "JTAG HS2 Programming Cable"

Downloads

File	File-Extension	Description
Bit-File	*.bit	FPGA Configuration File
Diverse Reports	--	Report files in different formats

Component	Description
IP-Interfaces	I2C, ASIO (AXI-Stream to IO), SPI-Flash, Uart

Application	Description
hello_world	Xilinx Hello World Example

File	File-Extension	Description
MCS-File	*.mcs	Flash Configuration File with Boot-Image (MicroBlaze or FPGA part only)
Bit-File	*.bit	FPGA Configuration File
Software-Application-File	*.elf	Software Application for Zynq or MicroBlaze Processor Systems
Hardware-Platform-Specification-Files	*.hdf	Hardware Specification from the vivado project. Used in SDK/HSI
MMI-File	*.mmi	File with BRAM-Location to generate MCS or BIT-File with *.elf content (MicroBlaze only)
Diverse Reports	--	Report files in different formats

Component	Description
Xilinx-IP	I2C,SPI-Flash,UART
TE-IP	ASIO (AXI-Stream to IO)

Application	Description
hello_world	Xilinx Hello World Example

File	File-Extension	Description
MCS-File	*.mcs	Flash Configuration File with Boot-Image (MicroBlaze or FPGA part only)
BIT-File	*.bit	FPGA Configuration File
Software-Application-File	*.elf	Software Application for Zynq or MicroBlaze Processor Systems
Hardware-Platform-Specification-Files	*.hdf	Exported Vivado Hardware Specification for SDK/HSI
MMI-File	*.mmi	File with BRAM-Location to generate MCS or BIT-File with *.elf content (MicroBlaze only)
Diverse Reports	--	Report files in different formats

Component	Description
Xilinx-IP	VIO
TE-IP	Startupe2,LabTools Frequency Counter

File	File-Extension	Description
BIT-File	*.bit	FPGA Configuration File
DebugProbes-File	*.ltx	Definition File for Vivado/Vivado Labtools Debugging Interface
Diverse Reports	---	Report files in different formats
LabTools Project-File	*.lpr	Vivado Labtools Project File

Component	Description
Xilinx-IP	VIO (Virtual Input/Output)
TE-IP	Labtools Frequency Counter, Startupe2 Primitive Wrapper

File	File-Extension	Description
BIT-File	*.bit	FPGA Configuration File
DebugProbes-File	*.ltx	Definition File for Vivado/Vivado Labtools Debugging Interface
Diverse Reports	---	Report files in different formats
LabTools Project-File	*.lpr	Vivado Labtools Project File
MCS-File	*.mcs	Flash Configuration File with Boot-Image (MicroBlaze or FPGA part only)

Directory	Content
PCN	Product change notifications: Important changes between hardware revisions
Reference Design	Reference Designs sort by ISE/EDK Version
REV0x	Documents and source files sorted by PCB revision. Connector Pinout Viewer/XDC-Generator available on TE Master Pinout, as well as a additional informations on All Trenz Electronic SoMs
	Documents	PDF documents, like Technical Reference Manual, Schematics, Assembly Diagrams and...
	Firmware	Initial configuration for diverse PCB components, like CPLD, PLL and ...
	HW Design	Relevant files for PCB-Design, like PCB-STEP-Model, Cooler-STEP-Model, Trace-length, Altium libraries / projects (only for selected carrier boards), and ...
	Pictures	PCB-Pictures

Directory	Content
PCN	Product change notifications: Important changes between hardware revisions
REV0x	Documents and source files sorted by PCB revision. Connector Pinout Viewer/XDC-Generator available on TE Master Pinout, as well as a additional informations on All Trenz Electronic SoMs
	Documents	PDF documents, like Technical Reference Manual, Schematics, Assembly Diagrams and...
	Firmware	Initial configuration for diverse PCB components, like CPLD, PLL and ...
	HW Design	Relevant files for PCB-Design, like PCB-STEP-Model, Cooler-STEP-Model, Trace-length, Altium libraries / projects (only for selected carrier boards), and ...
	Pictures	PCB-Pictures

Component	Description
Interface IPs	DDR3, GPIO, Uart0, QSPI and Ethernet

Application	Description
hello_world	Xilinx Hello World Example (.elf file only)

File	File-Extension	Description
MCS-File	*.mcs	Flash Configuration File with Boot-Image (MicroBlaze or FPGA part only)
Bit-File	*.bit	FPGA Configuration File
Software-Application-File	*.elf	Software Application for Zynq or MicroBlaze Processor Systems
Hardware-Platform-Specification-Files	*.hdf	Hardware Specification from the vivado project. Used in SDK/HSI
MMI-File	*.mmi	File with BRAM-Location to generate MCS or BIT-File with *.elf content (MicroBlaze only)
Diverse Reports	--	Report files in different formats

Component	Description
Xilinx-IP	MicroBlaze, MB-Debug, Uartlite, MIG7 for DDR3, QSPI, Timer, Ethernet Lite
TE-IP	ASIO GPIO (AXI-Stream to GPIO)

Application	Description
Hello World	Xilinx Hello world ( generate elf file only)

File	File-Extension	Description
MCS-File	*.mcs	Flash Configuration File with Boot-Image (MicroBlaze or FPGA part only)
BIT-File	*.bit	FPGA Configuration File
Software-Application-File	*.elf	Software Application for Zynq or MicroBlaze Processor Systems
Hardware-Platform-Specification-Files	*.hdf	Exported Vivado Hardware Specification for SDK/HSI
MMI-File	*.mmi	File with BRAM-Location to generate MCS or BIT-File with *.elf content (MicroBlaze only)
Diverse Reports	--	Report files in different formats

Component	Description
Xilinx-IP	VIO,ILA
TE-IP	unio_mac

File	File-Extension	Description
BIT-File	*.bit	FPGA Configuration File
DebugProbes-File	*.ltx	Definition File for Vivado/Vivado Labtools Debugging Interface
Diverse Reports	---	Report files in different formats
Hardware-Platform-Specification-Files	*.hdf	Exported Vivado Hardware Specification for SDK/HSI
LabTools Project-File	*.lpr	Vivado Labtools Project File

Component	Description
Interface IPs	QSPI, Uart, ASIO (Axi-Stream to IO)

Application	Description
hello_world	Xilinx Hello World Example

File	File-Extension	Description
MCS-File	*.mcs	Flash Configuration File with Boot-Image (MicroBlaze or FPGA part only)
Bit-File	*.bit	FPGA Configuration File
Software-Application-File	*.elf	Software Application for Zynq or MicroBlaze Processor Systems
Hardware-Platform-Specification-Files	*.hdf	Hardware Specification from the vivado project. Used in SDK/HSI
MMI-File	*.mmi	File with BRAM-Location to generate MCS or BIT-File with *.elf content (MicroBlaze only)
Diverse Reports	--	Report files in different formats

Component	Description
Xilinx-IP	ILA, VIO, CLK-Wizard
TE-IP	F32C, Vector_LED, UART_MON

File	File-Extension	Description
BIT-File	*.bit	FPGA Configuration File
DebugProbes-File	*.ltx	Definition File for Vivado/Vivado Labtools Debugging Interface
Diverse Reports	---	Report files in different formats
LabTools Project-File	*.lpr	Vivado Labtools Project File
MCS-File	*.mcs	Flash Configuration File with Boot-Image (MicroBlaze or FPGA part only)

Component	Description
IP-Interfaces	DDR3, QSPI, Uart, I2C, Ethernet, ASIO (AXI-Stream to IO)

Application	Description
hello_world	Xilinx Hello World Example (.elf only)

File	File-Extension	Description
MCS-File	*.mcs	Flash Configuration File with Boot-Image (MicroBlaze or FPGA part only)
Bit-File	*.bit	FPGA Configuration File
Software-Application-File	*.elf	Software Application for Zynq or MicroBlaze Processor Systems
Hardware-Platform-Specification-Files	*.hdf	Hardware Specification from the vivado project. Used in SDK/HSI
MMI-File	*.mmi	File with BRAM-Location to generate MCS or BIT-File with *.elf content (MicroBlaze only)
Diverse Reports	--	Report files in different formats

Component	Description
Xilinx-IP	AXI Timer, AXI Interrupt Controller,MIG, AXI QSPI, AXI Uart Lite, AXI I2C, AXI Ethernet Lite, VIO
TE-IP	ASIO (AXI-Stream to IO), labtools_fmeter

Application	Description
hello_world	Xilinx Hello World Example (.elf only)
te_spi_bootloader	SPI Bootloader (.elf only)

File	File-Extension	Description
MCS-File	*.mcs	Flash Configuration File with Boot-Image (MicroBlaze or FPGA part only)
BIT-File	*.bit	FPGA Configuration File
Software-Application-File	*.elf	Software Application for Zynq or MicroBlaze Processor Systems
Hardware-Platform-Specification-Files	*.hdf	Exported Vivado Hardware Specification for SDK/HSI
MMI-File	*.mmi	File with BRAM-Location to generate MCS or BIT-File with *.elf content (MicroBlaze only)
Diverse Reports	--	Report files in different formats

Component	Description
Xilinx-IP	AXI Timer, AXI Interrupt Controller,MIG, AXI QSPI, AXI Uart Lite, AXI I2C, AXI Ethernet Lite

Application	Description
hello_world	Xilinx Hello World Example (.elf only)
memory_tests	Xilinx Memory Example (.elf only)

File	File-Extension	Description
BIT-File	*.bit	FPGA Configuration File
Diverse Reports	---	Report files in different formats
Hardware-Platform-Specification-Files	*.hdf	Exported Vivado Hardware Specification for SDK/HSI
LabTools Project-File	*.lpr	Vivado Labtools Project File
MCS-File	*.mcs	Flash Configuration File with Boot-Image (MicroBlaze or FPGA part only)
MMI-File	*.mmi	File with BRAM-Location to generate MCS or BIT-File with *.elf content (MicroBlaze only)
Software-Application-File	*.elf	Software Application for Zynq or MicroBlaze Processor Systems

Component	Description
Zynq Processor	activated MIO-Interfaces: DDR3, QSPI, GPIO,2x Uart, QSPI,2x I2C,2x SD,1x Ethernet

Application	Description
zynq_fsbl	Zynq First Stage Bootloader (for hdmi modified and provided as library in /sw_lib/)
hello_world	Xilinx Hello World Example

File	File-Extension	Description
Bin-File	*.bin	Flash Configuration File with Boot-Image for Zynq-FPGAs
Bit-File	*.bit	FPGA Configuration File
Software-Application-File	*.elf	Software Application for Zynq or MicroBlace Processor Systems
Hardware-Platform-Specification-Files	*.hdf	Hardware Specification from the vivado project. Used in SDK/HSI
BIF-File	*.bif	File with description to generate Bin-File
OS-Image	*.ub	Image with Linux Kernel (On Petalinux optional with Devicetree and RAM-Disk)
Diverse Reports	--	Report files in different formats